主要應用
◆阿霉素脂質體 Doxorubicin liposome
◆ 兩性霉素 B 脂質體 Amphotericin B liposome
◆ 紫杉醇脂質體 Paclitaxel liposomes
◆ 奧沙利鉑脂質體 Oxaliplatin liposomes
◆ 伊立替康脂質體 Irinotecan liposome
◆ SiRNA 脂質體 SiRNA liposome
◆ 白蛋白紫杉醇納米粒 Albumin paclitaxel nanoparticles
◆ 核酸類脂質體 Nucleic acid liposome
◆ mRNA脂質體 mRNA liposome
擠出原理
Extrusion Principle
樣品經過水化形成脂質體后，一般會通過高壓均質或者超聲的方式對樣品進行初步均質處理，處理后樣品粒徑和分布都會有所提高，但往往還不能達到所需要的理想要求。此時，將均質后樣品由下圖中進料口進入，通過高壓氮?dú)鈱悠窂臑V膜中擠出，擠出后的樣品粒徑和分布都會進一步提高。
After the sample is hydrated to form liposomes, the sample is usually homogenized by high-pressure homogenization or ultrasonic wave. After treatment, the particle size and distribution of the sample will be improved, but it can not meet the desired requirements. At this time, the homogenized sample enters through the feed port in the figure below, and the sample is extruded from the filter membrane by high-pressure nitrogen. The particle size and distribution of the extruded sample will be further improved.
支撐板
Support plate
支撐板和濾板主要起到支撐濾膜的作用。 由于磷脂有一定的相變溫度，所以在擠出之前需要對擠出器夾套通入恒溫水進行預熱至一定溫度（如70℃），且在使用過程中需保持在此溫度。通常的脂質體品種擠出之后粒徑能達到 100nm以下，PDI 能控制在 0.1 以下。
The supporting plate and filter plate mainly play the role of supporting the filter membrane. Since the phospholipid has a certain phase transition temperature, it is necessary to preheat the extruder jacket with constant temperature water before extrusion to a certain temperature (such as 70 ℃), which should be maintained in the process of use. After extrusion, the particle size of liposomes can reach below 100nm and PDI can be controlled below 0.1.
動力源：氮?dú)?/p>
Power source: nitrogen
技術特征
Technical features
◆核心部件 The core components
支撐板（SS316L不銹鋼）
Support plate (SS316L stainless steel)
濾板（SS316L不銹鋼）
Filter plate (SS316L stainless steel)
濾膜:PC材質（聚碳酸酯）
Filter membrane :PC material (polycarbonate)
密封系統：PU材質/聚四氟乙烯
Sealing system: PU material/polytetrafluoroethylene
溫控系統：夾套控溫
Temperature control system: jacket temperature control
◆技術特點 Technical characteristics
所有部件包括“O”型圈，墊圈均通過FDA 認證
All parts including "O" rings, gaskets are FDA approved
操作便捷，可重復使用
Easy to operate and reusable
嚴格控制產品粒徑，可單次操作或循環操作
Strictly control the particle size of products, single operation or cycle operation
裝卸方便，便于清洗和滅菌
Easy loading and unloading, easy cleaning and sterilization
所有數據可直接放大
All data can be directly amplified
預設壓力保護閥
Preset pressure protection valve
可用于高濃度樣品處理
Can be used for high concentration sample processing
可放在潔凈室中使用，符合 GMP 標準
Can be used in a clean room, accord with GMP standards
技術參數
Technical Parameter
2006-2024 上海博華國際展覽有限公司版權所有（保留一切權利）
滬ICP備05034851號-57
